Technology becomes Easy — just call us
Cabling Guide — Dubai & Sharjah

Cat6 vs Cat6A vs Fiber: Choosing Network Cabling for Your Office

How to choose and plan structured cabling for an office fit-out, warehouse or villa so it lasts for years.

By J&T Information TechnologyUpdated Networking & WiFi
Quick answer

For most new offices in the UAE, Cat6 is enough for desks, phones and cameras, and Cat6A is the better choice for Wi-Fi access points, server rooms and anything that may need 10 Gbps over long runs. Copper cable of either type is limited to 100 metres per run. Use fiber to connect floors, buildings, warehouses and racks that are further apart. Whatever you choose, the installation quality, labelling and test reports matter as much as the cable category.

Key takeaways

  • Copper Ethernet runs are limited to 100 m, including patch cords.
  • Cat6: 1 Gbps to 100 m, 10 Gbps only on short runs (about 55 m).
  • Cat6A: 10 Gbps to the full 100 m; better for Wi-Fi 6/7 access points and PoE.
  • Fiber: for backbones between floors, buildings and long distances.
  • Ask for labelled outlets, patch panels and a certified test report.

Cat6, Cat6A and fiber compared

Cat6Cat6AFiber (single-mode / multimode)
Typical speed1 Gbps (10 Gbps on short runs)10 Gbps10 Gbps and higher
Maximum run100 m (10 Gbps about 55 m)100 mHundreds of metres to many kilometres
Bandwidth rating250 MHz500 MHz—
Powers devices (PoE)YesYes, runs cooler at high powerNo (needs local power)
Best forDesks, IP phones, printers, camerasAccess points, server rooms, future-proof fit-outsFloor-to-floor and building-to-building links
Cost and sizeLowest, thinnerHigher, thicker and stifferCable is affordable; needs fiber switches/modules

Where each cable belongs

Desks and phones: Cat6 is normally enough. Most PCs and IP phones connect at 1 Gbps.

Wi-Fi access points: modern Wi-Fi 6E and Wi-Fi 7 access points can use more than 1 Gbps and draw more power. Cat6A gives them room to grow.

CCTV: Cat6 carries video and power (PoE) to cameras up to 100 m. For gates, car parks and perimeters further away, use fiber with a PoE switch near the cameras.

Backbone: connect each floor's network rack to the main rack with fiber, ideally with a spare core for redundancy.

Power over Ethernet (PoE) basics

PoE sends power through the network cable, so cameras, phones and access points do not need a socket. Standards include 802.3af (up to 15.4 W per port), 802.3at or PoE+ (up to 30 W) and 802.3bt (up to 60 W or 90 W). Check that the switch's total PoE budget covers every device connected to it.

Fit-out checklist

  1. Plan outlets with the furniture layout: at least two points per desk, plus printers, TVs and meeting rooms.
  2. Add ceiling points for access points and cameras before ceilings close.
  3. Keep every run under 90 m of fixed cable so patch cords fit within 100 m.
  4. Separate data cables from power cables to avoid interference.
  5. Use a properly sized rack with patch panels, cable managers and space for growth.
  6. Label both ends of every cable and every outlet with the same number.
  7. Ask for a test report for every point and a drawing showing outlet numbers.
  8. Put the rack on a UPS and make sure the room is cooled.

Signs your cabling needs fixing

  • Random disconnections or slow speeds on some desks only
  • No labels, so nobody knows which cable goes where
  • A tangled rack that is hard to work on
  • Cameras or access points dropping when the switch gets busy

Frequently asked questions

Is Cat6 enough for an office?

For desks, IP phones, printers and most cameras, yes. Choose Cat6A for Wi-Fi access points, server rooms and long runs where you want 10 Gbps.

What is the maximum length of a network cable?

A copper Ethernet channel is limited to 100 metres, including patch cords. For longer distances use fiber.

Can Cat6 do 10 Gbps?

Only on shorter runs, around 55 metres. Cat6A supports 10 Gbps over the full 100 metres.

Do I need fiber in my office?

You need fiber to connect network racks on different floors or buildings, or where cable runs exceed 100 metres, such as warehouses and car parks.

What should a cabling contractor hand over?

Labelled outlets and patch panels, a drawing with outlet numbers, and a test report for every cable point.

This guide is general information to help you plan. Requirements and products change, so confirm details for your own site before you buy or install.

Need IT Help in Dubai or Sharjah?

Call or WhatsApp J&T — we answer fast, diagnose first, and quote before any work starts.